Gate Company in Portland - On-Site in 60 Minutes, Fixed the Same Day

Gate Company in Portland, OR

If you’re planning a new automatic gate on a Portland lot, the job starts with the space you actually have, not the gate you saw online. Portland’s infill lots and narrow side yards leave inches between a swing gate and the property line, and the wet winters here punish cedar and fir faster than almost anything else. We install, repair, and service gate operators, and we work on the gate you have rather than pushing you toward the one brand we happen to carry. Call (855) 473-7281 and we’ll set up a free on-site estimate.

Call (855) 473-7281

Why Portland Homes Are Different

Gate work in Portland is shaped by two things that pull in opposite directions: a climate that eats wood, and a building pattern that leaves very little room to work.

The wet winters and moss-friendly damp here rot, swell, and sag wood gates at the hinge points. Freeze-thaw cycles and heavy rain warp boards and rust steel hardware. Then the dry stretch of summer shrinks those same boards and throws latches and hinges out of alignment, so a gate that closed cleanly in March catches in August. Cedar and fir gates in particular take a beating, and a hand-built wood gate on a pre-1930 bungalow lot is a very different repair from a modern infill gate squeezed against a fence line.

The other half is space. Portland’s post-2010 infill construction and the ADU boom put narrow side yards and tight driveways on lots that were never meant to hold a second structure and a car. On close-in and eastside lots, a gate often sits tight to the property line, which means swing clearance and hinge-side clearance, not just the hardware, decide whether a repair is even possible without a setback conversation. That’s the part most general contractors underestimate.

Our Main Portland Services

Two jobs come up more than any other in Portland: fixing a gate that’s sagging, stuck, or dead, and getting an electric operator back online. Both have their own pages.

Gate Repair in Portland

Most of the calls we get for gate repair in Portland come down to wood movement. A gate that dragged all summer suddenly clears in November, or a hinge that held for years tears out of softened fir after a wet spring. We diagnose the actual failure first: hinge plates pulling from rotted posts, latches out of alignment, sagging leaf edges, damaged frames. On tight infill lots we also check whether the swing has been fighting the property line all along, because adjusting hardware won’t fix a gate that never had clearance. Our technicians have up to 13 years of experience with this exact problem.

Electric Gate Repair in Portland

When an automatic gate stops responding, the failure is usually in the control board, a loop detector, a keypad, or the motor assembly, and it takes a technician who knows the system to tell which. Our electric gate repair work covers all of those on Linear, Viking, Ghost Controls, DoorKing, and the other operators we know well. Portland’s wet winters are hard on outdoor control enclosures and underground wiring, so we look at moisture intrusion and connections alongside the electronics. We diagnose what’s actually broken instead of quoting a full replacement.

Gate Installation in Portland

Installing a gate in Portland means fitting a modern access-control system into a lot that was platted before anyone owned a car. On post-2010 infill and ADU properties, the driveway is often a slot only inches wider than the vehicle, and the property line sits right where the gate needs to swing. Add cedar and fir that swell and warp through a wet winter and shrink through a dry August, and the gate has to be built with that movement in mind, not against it. Our Gate Installation work starts with measuring the actual clearance and the actual soil, then matching the operator and gate style to what the site allows. We install from a free on-site estimate, so you’ll have a written price before anything is ordered or dug.

Automatic Gate Installation

Signs you need it

You’re tired of getting out to open a manual gate in the rain, or you’ve bought an opener and found your driveway, slope, or side-yard clearance doesn’t fit a standard swing.

What it costs in Portland

A typical automatic gate installation in Portland runs $3,500 to $8,000, with complex sites on tight infill lots landing at the higher end, and the written estimate sets the final price.

How we do it

We measure the opening, confirm the swing direction and hinge-side clearance against the property line, check the power source, then set posts to proper footing depth and mount the operator and safety edges.

Driveway Gate Installation

Signs you need it

Your driveway gate is failing at the hinges or the frame, or you’re adding a secure entrance to a property where the old gate was hand-built decades ago.

What it costs in Portland

Driveway gate installation typically runs $2,500 to $6,500 in Portland depending on width, material, and operator choice, with the written estimate fixing the final price.

How we do it

We confirm the driveway grade and drainage, set the posts to the right depth, hang the gate for correct swing and clearance, then wire and test any operator, keypad, or loop detector.

What Gate Installation Costs in Portland

Price in Portland climbs with site difficulty: a narrow infill side yard that limits swing, a slope that needs a different operator, or a long power run to the gate location all add labor. The written estimate you get from the free on-site visit sets the final price, and we don’t start work until you’ve agreed to it.

Do I need a permit to install a gate in Portland?

Most gate installations that involve new posts, electrical work, or a structure near the property line need a permit, so ask the city’s building department before ordering. We’ll flag what’s likely to need one during the estimate.

Can you install a gate on a narrow Portland side yard?

Often yes. On tight infill lots we check hinge-side clearance and swing direction first, and sometimes a sliding gate or a different hinge configuration works where a standard swing won’t. The on-site measurement tells us which.

Brands We Service in Portland

We work on the operator you already have, including Linear, Viking, Ghost Controls, and DoorKing, along with the other major gate brands. No stocked parts and no brand loyalty pushing a swap: we diagnose on-site and order what the repair needs. See our brands for the full list. Most straightforward repairs turn around within a visit or two once parts arrive, and we tell you upfront when a part has to be ordered.

Pricing for Gate Company in Portland, OR

Neighborhoods We Serve in Portland

We cover gate work across Portland, from the close-in eastside lots where gates sit tight to the property line to the newer infill subdivisions out toward the city edges. Because the housing and the lots change so much block to block, the on-site estimate matters more here than in most cities. Fast dispatch runs from 7am to 7pm, Sunday through Friday, and we book the next opening that fits your job.

• Laurelhurst
• Sellwood
• Alberta Arts District
• Mount Tabor
• St. Johns

Service Area – Cities Near Portland

Gate work doesn’t stop at the Portland city line. We also take jobs in Milwaukie, OR, Lake Oswego, OR, Happy Valley, OR, and Beaverton, OR. Each of those areas has its own mix of older wood gates and newer infill construction, so the estimate process is the same: we look at the actual site before quoting a number. Call (855) 473-7281 to find out whether your address falls within our service area.

FAQs About Gate Company in Portland