Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Cedar Mill, OR
If you live along the Cornell Road corridor or up in the 97229 hills, your gate is doing two jobs at once: it secures the property and it has to look right to the community around it. That combination shapes most of the gate installation work we handle in Cedar Mill. The housing stock here is mostly 1980s through 2000s suburban subdivisions, plus some newer construction near the Hillsboro line, and the gates on those lots are now the same age as the homes. Wood and composite privacy gates have moved through decades of wet winters, and aluminum driveway gates sit on fence lines that have shifted in the clay-heavy soil. Ours is gate work only, which is why we can sort out an old wooden gate in a hillside backyard and a new automatic driveway gate on the flat the same week. Call (855) 473-7281 to talk through what you have.
Why Cedar Mill Homes Are Different
The single biggest factor in Cedar Mill gate work is the wet Willamette Valley winter. Months of rain soak and swell wood gates, rust untreated steel hardware, and push footing depth problems to the surface in the clay-heavy soil under the neighborhoods off Cornell and Saltzman. That shows up as seasonal hinge failures, gates that drag across the drive, and latches that quit lining up every fall. Cedar Mill’s distinctive twist is HOA oversight. Much of the housing sits inside master-planned, HOA-governed subdivisions, so a repair has to match community design standards, and property managers often need documentation of what was done. We keep that in mind before we pick hardware: an automatic driveway gate behind a code-enforced fence line can’t be patched with the wrong finish. Then there’s terrain. The Tualatin Hills slope neighborhoods have gates on grades, which loads hinges harder and misaligns latches faster than flat-lot builds. Fall storms add wind load and debris to the same gates. Our technicians have up to 13 years of experience, and that mix of clay soil, grade, and community rules is part of nearly every estimate we write here.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Main Cedar Mill Services
Most homeowners and property managers around Cedar Mill call us about two things: an old gate that has stopped working properly, or a gate operator that has quit. Here is how each one looks on the ground.
Gate Repair in Cedar Mill
Repair work in Cedar Mill usually starts with something the weather did. A wooden privacy gate that has swollen against its posts, a hinge that gave out after a wet season, or a driveway gate whose latch no longer meets because the ground shifted under it. On the grade lots off Cornell and Saltzman, sagging hinges are the most common complaint because the gate’s own weight pulls against the slope. We look at the gate, the posts, the footing, and the hardware together before recommending a fix. If the gate is worth keeping, we repair it. For more on that side of the business, see Gate Repair in Cedar Mill.
Electric Gate Repair in Cedar Mill
When an electric gate stops, the gate itself is often fine and the problem sits in the operator, the control board, a loop detector, a keypad, or the motor assembly. We work on the system that’s actually installed, whether it’s a LiftMaster unit or a Linear operator, rather than steering you toward a full replacement because a brand is unfamiliar. In Cedar Mill, we also check for water intrusion around the operator housing and any power run that has been stressed by a wet winter. If your gate won’t open or close reliably, that’s generally the first place to look. Read more about Electric Gate Repair in Cedar Mill and what we can do.
Gate Installation in Cedar Mill
New gate installation in Cedar Mill is usually a two-part job: fitting the gate to the property, then fitting it to what the neighborhood and the HOA will accept. The housing here spans decades, from older subdivisions where the fence line has settled to newer Hillsboro-adjacent builds where the gate has to match a clean, recent design standard. What we install most often are driveway gates on residential properties and automatic gates where a homeowner wants to stop getting out of the car. When a gate is being replaced rather than repaired, the work usually starts with an on-site measurement, then a written price, then scheduling for the install once the gate and operator are in hand. Through Gate Installation, we take on new gate projects across Cedar Mill, from a single privacy gate on a side yard to a full automatic driveway system with an operator and access control. The hillside lots off Cornell and Saltzman need a bit more care than flat-lot builds: the gate has to be hung to the grade and the posts set to proper footing depth so it doesn’t drift and drag within a season.
Automatic Gate Installation
Most of the automatic gates we install in Cedar Mill are driveway gates where the homeowner wants their car to come and go without getting out, and the operator has to be right for the gate’s weight and the slope it sits on.
Signs you need it
You’re getting out to open the gate every time, or the gate you have was never automated and there’s no operator on it at all.
What it costs in Cedar Mill
Automatic gate installation here typically runs $3,500 – $7,500 for the gate, operator, and controls, depending on gate size, material, and whether a power run has to be added.
How we do it
We measure the opening on-site, specify the gate and a matched operator, run the power and safety edges, mount the operator, set the travel and force limits, and test every safety input before we hand it over.
Driveway Gate Installation
A driveway gate on a Cedar Mill property is as much about what the HOA will approve as about the gate itself, and we plan the install around both. Aluminum and wood driveway gates both come up often here.
Signs you need it
Your driveway is open to the street, the old gate has reached the end of its life, or you’re adding a gate for the first time and want it to match the community’s look.
What it costs in Cedar Mill
Driveway gate installation typically falls in the $1,800 – $4,500 range for a manual gate, and $3,500 – $7,500 when you add the operator and controls.
How we do it
We measure the driveway opening and sight lines, set the posts to proper footing depth for the soil and grade, hang the gate to swing clean and level, then confirm the latch and any operator alignment.
What Gate Installation Costs in Cedar Mill
Every gate is quoted per job from a written estimate, and these ranges are typical figures, not a fixed price. The written estimate you get after we see the property is the price that holds.
| Item | Typical range in Cedar Mill |
|---|---|
| Manual driveway gate, supply and install | $1,800 – $4,500 |
| Automatic gate with operator and controls | $3,500 – $7,500 |
| Gate operator only, supplied and installed | $900 – $2,800 |
Do I need a permit to install a gate in Cedar Mill?
That depends on the gate, the operator, and the electrical run. Ask the city about permitting and check with your HOA before ordering, since community design standards often apply. We’ll walk you through what a typical install needs.
Will a new gate need to match HOA design rules in Cedar Mill?
Usually, yes. Many Cedar Mill subdivisions are HOA-governed, so the gate’s material, finish, and style often need approval. We can document the spec we’re installing so you can submit it to the board, which saves a rebuild later.
Brands We Service in Cedar Mill
We work on the gate you have. That’s the whole idea behind being brand-agnostic: we’re familiar with Linear and DoorKing operators as readily as we are with a Ghost Controls system, and we diagnose the actual unit in front of us. We don’t stock parts locally, so if a part is needed we source it and get back to you on timing. See our brands for the full list of systems we handle.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Cedar Mill, OR
These are the typical ranges for the work we do around Cedar Mill. The written estimate sets the final price, and we quote and agree the price with you before any work starts.
| Service | Typical range in Cedar Mill |
|---|---|
| Manual driveway gate, supply and install | $1,800 – $4,500 |
| Automatic gate with operator and controls | $3,500 – $7,500 |
| Gate operator only, supplied and installed | $900 – $2,800 |
Two things push price up in Cedar Mill: the grade and footing work on hillside lots, and any power run that has to be added to reach an operator. A gate on a slope or an HOA-enforced design standard often needs a bit more prep than a flat-lot install. We quote on-site and put the price in writing, so you know the number before we start.
Neighborhoods We Serve in Cedar Mill
Cedar Mill covers a lot of ground, from the subdivisions along Cornell Road to the homes that sit up in the 97229 hills and the newer builds closer to the Hillsboro line. Whether your gate is on a flat lot near the Milltowner area or on a graded driveway off Saltzman, the traffic is generally on the lighter side, so scheduling an on-site estimate is usually a straightforward matter. We dispatch Sunday through Friday, 7am to 7pm, and fast dispatch is available for repair calls.
- Cornell Road corridor
- Saltzman Road neighborhoods
- 97229 hills subdivisions
- Milltowner and nearby streets
- Hillsboro-adjacent new construction
Service Area – Cities Near Cedar Mill
Cedar Mill sits in a pocket where several communities meet, and we cover the gate work across the area. If you’re just outside Cedar Mill, we can usually get to you without much fuss. We work in Bethany, OR and Oak Hills, OR, both a short drive away, and we cover Beaverton, OR and Portland, OR as well. Tell us where you are and we’ll confirm scheduling. Call (855) 473-7281 for a free estimate.
Serving Cedar Mill, OR – Our Local Coverage Area
We serve Cedar Mill and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Gate Company in Cedar Mill
Call (855) 473-7281 and we’ll set up an on-site estimate. Installation is measured, ordered, and scheduled rather than same-day, so we’ll figure out the timeline with you. The price is quoted and agreed before any work starts.
We can document the spec we install, which helps with HOA approvals in Cedar Mill’s master-planned subdivisions. Check your community’s design standards first, and we’ll supply the details you need for the board.
Ask the city building department about permits for your install, since requirements vary with the gate and the electrical work. Then check with your HOA on design standards. We can walk you through what’s typically needed before you order.
What happens when you call
- 1A real person answersNo phone trees. Talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within 60 minutes.
- 4You approve before work beginsNothing starts until you say go.
What Cedar Mill Customers Say
"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Carlos Delgado"The loop detector under the driveway had failed and residents were stuck holding the button. He traced it, found the break, and had the exit loop reading cars again the same visit."
- Brian Schaefer"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
- Brooke Gallagher